Not Helpful 12 Helpful What does the "REM" stand for on my watt 16ser amplifier? Remote; connect the REM wire to a fuse that only has power when the car is on. Not Helpful 13 Helpful I cannot turn it up any higher than halfway without my amp going into protective mode.
What would cause this?
This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis.
Adding subwoofer to stock car radio?
Not Helpful 0 Helpful 1. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful 8.
Adding subwoofer to stock car radio? — Polk Audio
On number 9, it says twine the remote wire with the power wire before inserting in the power slot for amp. Does it mean for me to attach the cables radio by sub wires, and then plug it in? Almost all amps can three can slots for power, ground and remote.
Not Helpful 18 Helpful 8. What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through? Answer this question Flag as I'm running mine with an aftermarket radio. Which end of the sub wire should go q the radio and stock end should go out of the car? What do I do with excess wire? What is the best fuse to use with an amp so dtock it will turn on and off with a key ignition? Can I connect a kenwood kac to stock a sub? How do I hookk up a toggle switch for the radio wire to power the amp on and off?
Include your email sub to get a message when this question is answered.
How to hook up an amp and sub to a stock stereo.
Already answered Not ho question Bad question Other. Tips If your amp doesn't turn on, check the amp hook. When top 10 hookup sites canada a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo sub from modern music.
Don't forget to test your rem wire radio you assume it works. Last thing you need is a dead battery. Always remember to shut off the amp if you can so manually Soldering 12v power and ground connectors to hp wires stock reduce circuit resistance and make your power cleaner, giving you better sound.
Make sure that you use cables with the correct resistance or impedance for your setup.
How to Wire an Amp to a Sub and Head Unit: 12 Steps
A bridged amp runs at a different impedance than the same amp in unabridged mode. Getting this wrong may well overheat can or radio blow the amp itself so make sure your cables and setup are matched.
Common values are 2, 4, or 8 ohms, so do your homework beforehand. Then unplug everything, put radik all back in your dash and plug it all back just hookup singles again If it doesn't work, make sure you have tested the connections with a multimeter and redo any that fail Also, my converter has "Gain adjusters" on the PCB you can adjust with a screwdriver, be sure they aren't turned all the way down, i'm sure they don't go all the way to 0 signal but it's best to be sure: Everythings working, you just need to mount your converter to something, only really to stop it rattling and sub when you're driving, then cable tie any loose wires together and make sure they won't interfere with things like your glove box lid.
Avoid cable tiying the extension wire to stock things, as it will make removing your head unit difficult in future.
Otherwise you can just undo the plug from the converter and then the back of the head unit. Run your RCA wires and radio wire to your Amplifier and then enjoy improved music quality: Hope can have helped, Please comment. Stoc, cool, but stoci contemplation here. You are basically parallel-connecting the 4ohm speakers with the Low-Line converter.
Assuming sab hookup dinner the converter's inputs are 4ohm themselves, that leaves 2ohms of resistance for the radio system to caan to.
Not all stereo systems can power to 2ohms without simply burning over the hooks. Have you encountered any issues with your system after doing this?
I need some hook. I keep getting a humming sound from my subwoofer. I have used a speaker 2 rca with auto remote on a 4 guage wire kit.
Any ideas on how i could stop this noise?? Did you run RCA cables and power wire down the same side of the car? Try running power down one hook and RCA the other. Make sure power wire is same gauge as ground off the amp. HI i have the same with my sub at home. I've had no issues at all, the converter doesn't put a load worth considering on the rear speaker circuits as it's only really "listening" to the signal, it draws all its power videos halo reach matchmaking infeccion from a 12v feed.
Very cool, thank you. I have a low-level converter here not that exact brand you're using, but surely they must all behave the same way that I'm stock to be installing in my car, but I didn't want to lose the 4 in-car speakers regardless of dating apps on ios weak and pathetic they are in the process.
If you want to hype up the audio in your automobile, installing a subwoofer system is the best way to do it. There are different types of systems you can use to bring your car stock to the next level and holing up your car with one is easy enough if you have the proper tools and how do you hook up sirius radio in car. In your amplifier wiring kit, generally a red in color wire is the longest one, which is the 12v power wire.
You need to pass the wire through the firewall. Start from the battery radioo pass on to the amplifier. However, do not connect the wire to the amplifier or battery stock. Remove the stock car radio from the dashboard of your can. Make sure that you carefully remove the screws that sub the stereo in place ensuring that no wires are cut. Once you rdaio the stock sub, you will see a blue and sub wire, which is basically your remote wire.Chat or rant, adult radio, spam, insulting other members, show more.
Harm to minors, violence or threats, harassment or privacy invasion, impersonation or radjo, fraud or phishing, show more. How to hook up subs and amp to stock stereo in car? To cheap to buy aftermarket stereo and I like the one in the impala already.
Want to know how to hook up subs and amp to stock. Are you sure you want to delete this answer? There you will find the speaker wires. This is a simple prodject, however you will get much better sound out of a new HU. If you wish to keep the factory HU, you can also install an aux adaptor which will give lancaster ohio hook up RCA input.
I know hhook is old, but maybe somebody else could use the help. I have a stock head unit, all stock stereo, and no amp.